Ponding water after every rain
We find why the water is not leaving and fix the drainage, usually with tapered insulation, instead of patching a membrane that will pond again.
Modified bitumen — “mod bit” — is the two-ply asphalt membrane that has covered Houston's small flat roofs for generations: bungalow rear additions in the Heights, porch and garage roofs in Montrose, and the flat sections on 1920s–60s homes across the inner loop. It is tough, repairable and proven in Houston heat, and it is the right system where a small flat section needs a durable, multi-layer membrane. Call (346) 654-5170 and we will inspect the membrane, the deck and the drains.

A modified bitumen roof is two plies of asphalt membrane — a base sheet and a cap sheet — torched, self-adhered or cold-applied over insulation and cover board on a low-slope deck. We start by checking the deck and the drainage, then the membrane's laps, blisters and flashing. The system is at its best on small residential flat sections, where its multi-layer build-up tolerates foot traffic and small movements that would stress a single-ply membrane. Flat membranes in Houston last roughly 15 to 25 years, and modified bitumen sits in that range — less under standing water.
Modified bitumen is a conditional service in one sense: it belongs on flat and low-slope sections, and we install it where the roof calls for it — Heights bungalow additions, Montrose garage apartments, ranch additions in Sharpstown and Spring Branch. It does not belong on pitched roofs. Winter 2021's freeze-thaw cracked aged modified bitumen on flat sections across Houston, a reminder that old, brittle mod bit fails differently from old TPO. We publish no manufacturer tiers for modified bitumen, because none were found for this business — what we publish is the scope, in writing, before work starts.
A mod bit job is decided at the laps and the flashing. Here is what we cover.
We strip the failed two-ply modified bitumen cap sheet to the deck — the membrane is replaced and the deck is probed first, because on a flat section the cap sheet wears out long before the structure does.
Soft, rotted or delaminated decking is photographed and replaced. A new cap sheet over rotted decking is money wasted.
A base sheet goes down first, then the cap sheet, torched or self-adhered to specification with proper lap widths. Two plies are the system — one ply is a patch, not a roof.
Parapet, curb and penetration flashing is detailed by hand and sealed. These are the leak points on a mod bit roof, and they are never rushed.
We test drains and scuppers, clear blockages and check vents. A mod bit roof that cannot drain will pond, blister and fail early.
We walk the membrane, check laps and blisters, mark ponding that is still standing two days after rain, and scan the deck for trapped moisture. You get photos and a written scope before any work is agreed.
We strip the failed system to the deck, replace damaged sheathing and lay insulation and cover board, tapered where drainage needs it.
The base sheet goes down over the cover board, with laps set to specification and the deck properly prepared underneath. Torch-applied laps are rolled while hot so the bond sets as the sheet cools, and the roof is dried in before we leave.
Parapets, curbs and penetrations are flashed and sealed before the cap sheet goes on, so the details are built in, not added afterwards.
We walk the roof with you, check the drains, and show photos of the finished laps and flashing. If anything looks off after the job, call us and we will come back and look.
Mod bit is a torch-and-lap trade on small roofs. The tools are simple; the lap widths and flashing are what matter.
Finds trapped moisture under the cap sheet without tearing the whole roof up — blisters usually mark where water is already trapped.
Confirms whether decking under a blistered cap sheet is wet or dry, so we replace only what is damaged.
Fasten base sheet, insulation and cover board with consistent depth across the field.
Keep base and cap sheet courses and laps straight across the deck.
Keep the crew safe on roof edges and two-storey homes. Fall protection is standard on every job.
Lifts membrane rolls and materials onto the roof safely, without dragging them across finished work.
The situation: a 1920s Heights bungalow whose flat rear addition ponds after rain, with a blistered mod bit membrane and a soft spot near the wall.
How we approach it: we probe the deck, strip the failed membrane, replace damaged decking, and install a two-ply modified bitumen system over tapered insulation so water reaches the drain.
The situation: a garage apartment in Montrose with an ageing mod bit roof, cracked at the laps and leaking at a curb after heavy rain.
How we approach it: we inspect the laps and the flashing, then quote the full system — deck, insulation, base and cap sheet — rather than coating over a failed roof.
The situation: An apartment block in Gulfton with an ageing mod bit roof, blistered across the field and leaking at the parapets after every Gulf downpour.
How we approach it: we probe the deck, strip the failed membrane, replace damaged decking, and install a two-ply modified bitumen system over tapered insulation so water reaches the drain.
Mod bit fails at laps, blisters and flashing. These are the calls we get.
Ask a pro →We find why the water is not leaving and fix the drainage, usually with tapered insulation, instead of patching a membrane that will pond again.
Summer heat and trapped moisture blister mod bit; freeze-thaw cracks aged, brittle membrane. We cut out the failed sections, dry or replace the wet insulation underneath, and re-lay — a coating over a blister hides the problem.
Parapet, curb and penetration flashing are the most common mod bit leak points. We strip the detail back and re-flash it properly instead of coating over it.
Wind lifts laps and edges on an ageing mod bit roof. We re-secure and re-seal the affected laps, check the rest of the field, and quote replacement when the membrane has reached the end of its service life.
“I had completely roofing done on my house, Manny and his crew did great job! And they got the job done in a day then clean very good after all. Very happy!”
kim nguyenGoogle review · 6 months ago
✓ Google reviewThe reviews quoted on this page are word-for-word Google reviews of Bridgegate Construction LLC, shown with each reviewer's name as it appears on Google. We have read five of our 31 Google reviews — all 5 stars — and the rest appear only in that total. Read all 31 reviews on our Google profile.
As market context only — not a quote: Texas sources put two-ply modified bitumen at roughly $8 to $12 per square foot, though that figure comes from Dallas-area sources and Houston pricing was not separately verified. Scope matters more than the number — decking, insulation and drainage change it. We quote your roof in writing after inspecting it.
Flat membranes in Houston last roughly 15 to 25 years, and modified bitumen sits in that range — shorter where water ponds, longer where drainage works. The February 2021 freeze-thaw cracked aged modified bitumen on flat sections across Houston, which is why we inspect old mod bit carefully rather than assuming it has years left.
It depends on the roof. TPO is a white, heat-welded single-ply membrane that suits larger flat decks and commercial roofs. Modified bitumen is a two-ply asphalt system that suits small residential flat sections — additions, porches and garages — where its multi-layer build-up tolerates foot traffic and movement. We recommend by roof, not by habit.
Yes, inside the City of Houston a Residential Roofing Permit is required for a re-roof, with plan review and inspection, a $33.56 administration fee and about 10 business days' processing; roof covering of 100 square feet or less in aggregate is exempt. In unincorporated Harris County there is no residential roofing permit. Texas has no state roofing licence.
We will inspect the membrane, the laps and the drains, and give you a written scope. Call (346) 654-5170 or request an inspection online.
Schedule an inspection — (346) 654-5170 →Call (346) 654-5170 or send us a message and we will get back to you during office hours. Tell us what is happening with your roof and we will tell you what it takes to fix it. Office hours: Mon–Wed 8 AM–6:30 PM · Sat 9 AM–6:30 PM · Sun Closed.