EPDM rubber membrane for flat and low-slope roofs

EPDM Rubber Roofing in Houston

EPDM is the black rubber membrane that has covered flat roofs for decades — flexible, forgiving of movement, and proven on townhome decks, garage roofs and commercial buildings across Houston. Its seams are primed and taped rather than welded, so the quality of the seam preparation decides the life of the roof. If your flat roof is blistering, ponding or leaking at the seams, call (346) 654-5170 and we will inspect the membrane, the deck and the drains.

↗
Request a visit

Request service today

Tell us what is happening. Our local team will confirm your visit shortly.

No spam. No obligation. Just practical help.
Thanks — we'll call shortly to confirm your visit.
EPDM rubber membrane roofing in Houston
Careful work. Honest options.
About this service

What EPDM roofing in Houston actually involves

An EPDM roof is a single-ply synthetic rubber membrane, laid over insulation and cover board on a low-slope deck, with seams joined by primer and splice tape and flashing at parapets, curbs and penetrations. We start by checking the deck and the drainage — interior drains, scuppers and any ponding — then the membrane's seams, which are the known weak point: a seam laid over skipped or dirty primer fails first. EPDM suits roofs that move, flex or need a dark membrane, and it handles Houston heat well, though its black surface absorbs more heat than white TPO.

EPDM is a conditional service for us in one sense: it belongs on flat and low-slope roofs, residential and commercial, and we install it where the roof calls for it — townhome decks in Midtown and EaDo, garage and porch roofs, and commercial decks. It does not belong on pitched roofs. Flat membranes in Houston last roughly 15 to 25 years, and EPDM sits in that range when its seams are prepared properly. We publish no manufacturer certifications for EPDM, because none were found for this business — what we publish is the scope, in writing, before work starts.

  • ✓ Flexible rubber membrane, proven for decades
  • ✓ Primed and taped seams — preparation decides life
  • ✓ Suits roofs that move or flex
  • ✓ Flat and low-slope only, never pitched
What's included

What our EPDM roofing service includes

An EPDM job is decided at the seams. Here is what we cover.

✓

Full roof inspection

We walk the membrane, check seams, drains and ponding, and scan the deck for trapped moisture before quoting anything.

✓

Tear-off and disposal

We strip the failed EPDM rubber membrane and its insulation to the deck and haul it away — on a black rubber roof the seams and laps are where age shows first, so soft decking is found and fixed instead of covered over.

✓

New EPDM membrane

EPDM membrane is laid over new insulation and cover board, with seams primed and taped to specification and flashing at every parapet, curb and penetration.

✓

Seam primer and splice tape

Seams are cleaned, primed and taped with the right overlap — the step that decides whether an EPDM roof lasts or fails at the seams. We do not skip primer to save time.

✓

Flashing and termination

Parapet, curb and penetration flashing is detailed by hand, and the membrane is terminated properly at edges and walls.

✓

Photos and written scope

You get photos of the deck, the seams and the finished flashing, and a written scope of what was done.

How it works

How our EPDM roofing process works

01

Inspection and moisture scan

We walk the membrane, check seams for lifted splice tape and shrinkage at the edges, mark ponding that is still standing two days after rain, and scan the deck for trapped moisture. You get photos and a written scope before any work is agreed.

02

Written scope and pricing

We put the system in writing — membrane, insulation, flashing and drainage — so you can see exactly what is included before work starts.

03

Tear-off and deck prep

We strip the failed system to the deck, replace damaged sheathing and lay insulation and cover board, tapered where drainage needs it.

04

Membrane installation

EPDM is rolled out, seams are cleaned, primed, taped and rolled flat, and every parapet, curb and penetration is flashed and sealed. Taped seams need time to bond, so we keep foot traffic off the fresh seams until they have set — and where the roof gets regular foot traffic, around hatches and units, we add walkway protection.

05

Final inspection and walkthrough

We walk the roof with you, check the drains, and show photos of the finished taped seams and flashing. If anything looks off after the job, call us and we will come back and look.

Tools & methods

Tools and methods we use on EPDM roofs

EPDM is a preparation trade: clean, prime, tape, roll. The tools are simple; skipping a step is what fails.

Infrared leak detector

Finds trapped moisture under black rubber without tearing the whole roof up — on EPDM the stain rarely sits over the wettest deck.

Moisture meter

Confirms whether decking under a blistered EPDM membrane is wet or dry, so we replace only what is damaged.

Seam roller

Rolls primed and taped seams flat so the splice tape bonds fully across the joint. A seam that is not rolled is a seam that will lift.

Hot-air welder

Used where EPDM details and flashing need a welded joint, and on mixed-system transitions.

Roofing nail gun and air compressor

Fasten insulation and cover board with consistent depth across the field.

Safety harness and ladder stabilizer

Keep the crew safe on roof edges and two-storey townhomes. Fall protection is standard on every job.

Chalk line and pitch hoist

Keep membrane courses straight and lift rolls and materials onto the roof safely.

What the work looks like

Three situations we see often.

A Garden Oaks garage roof with a failed EPDM seam

The situation

The situation: a garage flat roof whose EPDM membrane is lifting at the seams after years of Houston heat, with water staining on the ceiling below.

How we approach it

How we approach it: we scan for trapped moisture, strip the failed membrane, replace wet decking, and install new EPDM with seams cleaned, primed, taped and rolled — then check the drain that let water sit.

A Midtown townhome deck that ponds after rain

The situation

The situation: a townhome flat deck that holds water for days after a Gulf downpour, with blistering membrane near the scupper.

How we approach it

How we approach it: we probe the deck, replace damaged sections, and install new EPDM over tapered insulation so water reaches the scupper instead of sitting on the membrane.

A Westchase office park deck with ponding at the drains

The situation

The situation: An office park deck in Westchase whose EPDM membrane ponds at the interior drains after every Gulf downpour, with seams lifting where water stands.

How we approach it

How we approach it: we scan for trapped moisture, strip the failed membrane, replace wet decking, and install new EPDM with seams cleaned, primed, taped and rolled — then re-pitch the drains so water actually leaves.

Problems we solve

EPDM roof problems we fix in Houston

EPDM fails at seams, drains and penetrations. These are the calls we get.

Ask a pro →
01

Seam failure from skipped primer

Seams laid over dirty or unprimed membrane lift first. We strip the failed seam back, clean and prime properly, and re-tape with the right overlap — then check the rest of the field for the same shortcut.

↗
02

Ponding water at drains and scuppers

We find why the water is not leaving and fix the drainage, usually with tapered insulation, instead of patching a membrane that will pond again.

↗
03

Hail pocks and bruised insulation

Hail pocks EPDM and bruises the insulation underneath. We document the damage and replace the affected sections, advising a cosmetic-only approach where the membrane is still watertight.

↗
04

Failed pipe boots and flashing

Pipe boots and curb flashing are the most common EPDM leak points. We strip the detail back and re-flash it properly instead of coating over it.

↗
Proof you can check

About Bridgegate Construction

✓
Founded in 2018Bridgegate Construction LLC, Houston
✓
Latino-owned businessAs listed on our Google profile
✓
Google 5.0 stars · 31 reviewsAll five-star, as shown on Google
✓
Owner: Emmanuel “Manny” ArroyoPresident and owner
✓
Based at CITYCENTRE, Memorial City800 Town and Country Blvd Ste 500, Houston, TX 77024
Customer reviews

What Houston customers say

We do not write, edit, or invent reviews: every review quoted here is a verbatim Google review of Bridgegate Construction LLC. There are 31 Google reviews in total, all 5 stars. Read all 31 reviews on our Google profile.

Good questions

Frequently asked questions about EPDM roofing

(346) 654-5170 →

As market context only — not a quote, and scope matters: Texas sources put EPDM at roughly $4 to $8 per square foot for residential and low-slope work, against $11 to $16 per square foot for commercial systems — same material, different scope. We quote your roof in writing after inspecting it.

Flat membranes in Houston last roughly 15 to 25 years, and EPDM sits in that range when its seams are prepared properly. Heat, UV and ponding shorten life; clean, primed, taped and rolled seams stretch it. Lifespan is a trade range, not a promise — it depends on the roof, the seams and the drains.

It depends on the roof. TPO is white, reflective and heat-welded, and suits most Houston flat decks. EPDM is black, flexible and suits roofs that move or need a dark membrane. We recommend by roof, not by habit — see our TPO roofing and flat roofing pages for the comparison.

Yes, inside the City of Houston a Residential Roofing Permit is required for a re-roof, with plan review and inspection, a $33.56 administration fee and about 10 business days' processing; roof covering of 100 square feet or less in aggregate is exempt. Commercial re-roofs follow the City's commercial permit process. In unincorporated Harris County there is no residential roofing permit. Texas has no state roofing licence.

Ready when you are

Get your EPDM roofing estimate in Houston

We will inspect the membrane, the seams and the drains, and give you a written scope. Call (346) 654-5170 or request an inspection online.

Schedule an inspection — (346) 654-5170 →
Request an appointment

Contact Bridgegate Construction

Call (346) 654-5170 or send us a message and we will get back to you during office hours. Tell us what is happening with your roof and we will tell you what it takes to fix it. Office hours: Mon–Wed 8 AM–6:30 PM · Sat 9 AM–6:30 PM · Sun Closed.

Call anytime(346) 654-5170Call the office(346) 654-5170
Office hoursMon–Wed 8 AM–6:30 PM · Sat 9 AM–6:30 PM · Sun Closed. Thursday–Friday: hours not listed on our Google profile — call (346) 654-5170.
Request received — our team will be in touch shortly.
Tap to call(346) 654-5170