Ceiling stain under an old skylight
We trace the stain to its entry point — usually the curb flashing, not the glass — then re-flash the detail properly and water-test the repair.
A skylight is a hole in your roof with glass in it — and in Houston, where wind-driven rain arrives sideways, the flashing and curb around it matter more than the unit itself. Skylight flashing and curbs are one of the most common leak sources we find, and most skylight leaks are flashing failures, not glass failures. We install new skylights during a re-roof, replace leaking units like-for-like, and repair flashing on existing skylights. Call (346) 654-5170 and we will inspect the curb, the flashing and the roof around it.

A skylight job is three jobs at once: the opening in the deck, the curb and flashing that keep water out, and the tie-in to the roofing around it. We start in the attic, checking the deck, the framing and the condition of any existing skylight, then plan the curb height, the flashing kit and the shingle or membrane tie-in. A new skylight cut into an existing roof is a different scope from a like-for-like swap during a re-roof, and both are different from a new opening — we quote the scope you actually have.
Skylight repair is part of the same service: we re-flash leaking curbs, replace fogged or cracked domes and glazing, and fix wind-lifted flashing after a storm. The best time to add or replace a skylight is during a re-roof, when the deck is open and the flashing can be built into the new system instead of cut into an old one. We claim no skylight brand as installed — no brand was verified for this business. What we publish is the scope, in writing, before work starts. If your ceiling stain sits under a skylight, the leak is usually the flashing or the curb, not the glass — but water travels, so we trace it before we quote it.
A skylight job covers the opening, the curb, the flashing and the tie-in. Here is what we cover.
We check the deck, the framing and the attic around the opening before cutting or setting anything. A skylight over a sagging deck is a leak waiting to happen.
The curb is framed to the right height for the roof pitch, and the flashing kit is installed step by step with the roofing — not caulked on afterwards.
The unit is set on the curb and tied into the shingles or membrane around it, with the flashing woven into the roofing courses so water sheds over, not under, the detail.
The interior opening is trimmed and patched where the work disturbed it. We do not leave a finished skylight with an unfinished ceiling around it.
Every skylight is water-tested before we leave, and we walk you through the flashing and the interior finish. If anything looks off after the job, call us and we will come back and look.
We inspect the deck, the framing and any existing skylight from the attic and the roof, and photograph what we find. You get a written scope before any cutting starts.
The opening is laid out from inside and outside so the skylight lands between framing members where possible, and the deck is cut cleanly.
The curb is framed, the leak barrier goes down around the opening, and the flashing kit is installed step by step with the roofing.
The unit is set on the curb and tied into the shingles or membrane around it, with flashing woven into the roofing courses.
We water-test the skylight, check the interior for any sign of entry, and walk you through the finished work.
Skylight work is measuring, cutting and flashing. The moisture meter matters most — it finds the leak before the saw comes out.
Finds moisture around a skylight curb and in the deck before we cut or quote. Most skylight leaks are flashing failures, and the meter proves it.
Tracks a leak to its entry point, which is rarely directly above the ceiling stain.
Cuts shingles cleanly around a skylight opening so the flashing weaves into the courses instead of sitting on top of them.
Fastens underlayment, flashing and shingles around the opening with consistent depth.
Keep the opening, the curb and the flashing courses square and straight.
Keep the crew safe on steep pitches and two-storey roofs. Fall protection is standard on every job.
Powers the nail gun and keeps the work area clear of debris around the opening.
The situation: a Heights bungalow hallway with no natural light, where the owners want a skylight — and a roof that is nearing replacement anyway.
How we approach it: we plan the skylight as part of the re-roof, so the curb and flashing are built into the new system instead of cut into an old roof, and the opening lands between framing members.
The situation: a ceiling stain under an older skylight after heavy rain, with the glass itself looking sound.
How we approach it: we trace the leak with a moisture meter, re-flash the curb properly and water-test the repair — replacing the unit only if the inspection shows it has actually failed.
The situation: A Museum District townhome whose flat-roof skylight leaks at the curb after every Gulf downpour, with the glass itself looking sound.
How we approach it: we trace the leak with a moisture meter, re-flash the curb properly and water-test the repair — replacing the unit only if the inspection shows it has actually failed.
Most skylight problems are flashing problems. These are the ones we are called about most.
Ask a pro →We trace the stain to its entry point — usually the curb flashing, not the glass — then re-flash the detail properly and water-test the repair.
A fogged unit has lost its seal; a cracked dome lets water in directly. We replace the unit like-for-like, re-flashing the curb at the same time.
Wind lifts flashing at skylight curbs, especially after a Gulf storm. We re-seat and re-flash the curb, check the surrounding shingles, and water-test the repair.
Condensation around a skylight often means poor attic ventilation or a cold bridge, not a leak. We check the attic ventilation and the curb insulation before quoting a repair.
“Absolutely wonderful service. Had an issue with my roof leaking and they were attentive and listened my concerns. They get on the roof and found and fix the leak then took care of the interior too. They even fixed a poorly done previous repair done by another company. I Would recommend”
Nate DorrGoogle review · 3 months ago
✓ Google review“My roof was getting close to the end of its life and had started leaking, plus there was some sagging. Manny was upfront with me from the start and took the time to explain my options so we could figure out what actually made sense for my situation. The replacement was done right, and I never got the feeling anyone was cutting corners. If you need a roofer you can actually trust to do the job carefully, I highly recommend this company.”
Liam YangGoogle review · 3 months ago
✓ Google reviewThe reviews quoted on this page are word-for-word Google reviews of Bridgegate Construction LLC, shown with each reviewer's name as it appears on Google. We have read five of our 31 Google reviews — all 5 stars — and the rest appear only in that total. Read all 31 reviews on our Google profile.
As market context only — not a quote, and the range is wide because the scope varies: Houston guides put skylight installation at roughly $1,200 to $2,800, with higher figures above $6,000 for complex jobs, and skylight leak repair at roughly $500 to $2,000. A like-for-like swap during a re-roof costs less than a new opening cut into a finished roof. We quote your job in writing after inspecting the roof and the attic.
They can — skylight flashing and curbs are one of the most common leak sources we find, because wind-driven rain in a Gulf storm arrives sideways and tests every flashing detail. A skylight installed with its curb and flashing built into the roofing system, and water-tested afterwards, holds up well. A skylight caulked onto an old roof does not.
Yes. During a re-roof the deck is open, so the curb and flashing can be built into the new roofing system instead of cut into an old one. A like-for-like swap at re-roof time is the lowest-risk skylight job there is.
A skylight installed as part of a re-roof falls under the City of Houston Residential Roofing Permit required for a re-roof, with plan review and inspection, a $33.56 administration fee and about 10 business days' processing. A new opening that changes the structure is a different scope and may need additional review. In unincorporated Harris County there is no residential roofing permit. Texas has no state roofing licence.
One call gets a crew on your roof to measure the opening, check the deck and price the job in writing. Call (346) 654-5170 for a written estimate.
Schedule an inspection — (346) 654-5170 →Call (346) 654-5170 or send us a message and we will get back to you during office hours. Tell us what is happening with your skylight or your roof and we will tell you what it takes to fix it. Office hours: Mon–Wed 8 AM–6:30 PM · Sat 9 AM–6:30 PM · Sun Closed.